Fireproof Safe Envelope Bag for Lipo Batteries

7 in x 9 in

Black or Silver Options

Fireproof Safe Envelope Bag for Lipo/Life Batteries

Dimensions (LxWxD): 185 x 75 x 60mm

Bag will fit DF95 Travel Battery Case

Replacement Stainless Steel Mast Bearings; one all stainless and the other option is stainless bearing and casing but with a rubber seal on both sides for added protection. 

Precision Bearings: Lower manufacturing tolerances compared to lower-rated bearings, resulting in smoother rotation and less friction.

3D printed Mast Heels for 11.1mm Mast section.

Come in two variants, flat and with a locating Tang.

Two Lengths, 5mm and 10mm, and a 0mm tang version

Mast Ram for your 11mm mast.   3D Printed parts fitted on 40mm M3 Stainless bolt with nylon nut

Modified 15 June 2026:   The thumb wheel is now fitted with a brass insert to improve the fit and usability of the Ram

Supplied in 2 variants.  Basic push ram or clip-on which clips around your mast

Product images are for reference only.   Printed parts black are PLA-CF (Carbon Fibre reenforced PLA) on Stainless Steel Bolt

Holder fits into a 7mm hole in your boat

3D printed fitting ready to take your crane and sail hanger.

Matched to the 11.1mm mast section with a top section of 3.2mm, thus suitable to be uses at your Top Limit Mark.  you may need to add some tape or paint the band to comply with class rules.

Available in Black or White

Designed for our cranes but will accept most other cranes that are at least 1.5mm thick.

Comes fitted with 2mm cone point grub screw as a bearing for your sail hanger.

MADE IN THE USA

Stainless Steel Clew fitting used for mainsail and jib clews. 

Available for 11mm and 10mm booms used in the International One Meter (IOM) class and weigh under 1.2g each. 

Laser cut from 316L (A4) Stainless steel plate before being tumble polished to remove all burrs and imperfections.

Slide onto your boom and then apply a light crimp using pliers to secure it in position.

To attach the sail use a pair of pliers to gently bend the leg of the fitting forwards to create sufficient gap to feed the clew of the sail onto the fitting and then bend the leg back.

MADE IN THE USA

Stainless Steel fairlead used for main and jib sheets, sized to allow a z-hook to pass through the sheet hole.

Available for 11mm and 10mm booms used in the IOM (International One Meter) class and weighs less than 0.9g.

Laser cut from 316L (A4) Stainless steel plate before being hand reamed to remove sharp edges of the sheeting hole and then tumble polished to remove all burrs and imperfections.

Slide onto your boom and then apply a light crimp using pliers to secure it in position.

Mint Set of Deck Patches for Servo Hatch and/or Rear Deck (10 packs)

Mint Set of Deck Patches for mainsheet post fitting, winchline fitting and transom patch (pack of 5 each)

Joysway Mint IOM PNP Version without rigs and sails. 

Make own rigs and install in ready to go boat. 

Fully fitted Hull, Electric components, Keel, Rudder, No rig kit or sails.

Plug-n-Play Version:

Rigging Manual Here

FULL PRICE is $2400 plus shipping. 

///

The Joysway IOM (PNP Version)

• ABS Hull
• Carbon keel fin and rudder
• Carbon coated keel bulb
• Sail and Rudder Servos 
• Complete A Rig (2 piece mast) and Sails with colored luff tape matching hull
• Boat stand with laydown function
  
• Mint customized brushless waterproof winch servo (7.4V 28.0 kgf.cm, 0.36s/360°)
• Mint customized brushless waterproof rudder servo (7.4V 10.0 kgf.cm, 0.04s/60°).
• NOT INCLUDED; battery, receiver and transmitter.

Mint Jib Boom Rear End Fitting including metal fitting and screw