Lipo battery for the Mint, IOMs, EC12s, Soling 1M, Star 45, etc 

Key Features:

• Superior Discharge rate
• Low Internal Resistance (IR)
• Outstanding Cycle Performance
• Delivers full capacity and discharge
• Ideal for Scale Fixed Wing and RC Helicopters

Pack Specification:

• Capacity: 1300mAh
• Cell Count: 2s
• Voltage: 7.4V
• Constant Discharge: 45C
• Peak Discharge: 90C
• Maximum Charge Rate: 5C
• Battery Size: 75 x 34 x 14mm
• Battery Weight: 77g
• Charge Plug: JST-XHR
• Discharge Plug: XT60

6mm OD x 1.25mm ID x 3mm H

Used for Jib Pivot Connections as well as Backstay Connection on certain boats such as Proteus, K2, etc. 

Great battery for the DF95.

10C discharge provides plenty of power on demand while increasing battery life versus 25C versions.

Battery Specification: 

• Capacity: 850mAh
• Cell Count: 2s
• Voltage: 6.6V
• Constant Discharge: 10C
• Peak Discharge: 20C
• Maximum Charge Rate: 3C
• Battery Size: 55 x 30 x 16mm  
• Battery Weight: 47g
• Charge Plug: JST-XHR
• Discharge Plug: JR

Mint IOM A Sails Suit (supplied with white tapes and patches, no wires)

Mint IOM B Sails Suit (supplied with white tapes and patches, no wires)

Barnegat Bay A Cat Class Car Burgee in ABS

Each burgee has 3M car adhesive to install on car/boat/window

Bowsies (10 pack)

Mint IOM C Sails Suit (supplied with white tapes and patches, no wires)

2 Part Mast fully fitted including Gooseneck & Kicking Strap.
Booms fully fitted.
All rig fittings excluding rigging wire.

2 Part Mast fully fitted including Gooseneck & Kicking Strap.
Booms fully fitted.
All rig fittings excluding rigging wire.

1 Part Mast fully fitted including Gooseneck & Kicking Strap.
Booms fully fitted.
All rig fittings excluding rigging wire.

3D printed tool to enable quick and easy adjustment of fittings on your spars.

Used to move fitting forwards and backwards as well as rotating them, without risking any damage to your spar.

3D printed tool to make fitting of our components easier.   Suitable for spars between 10 and 11mm.

Components fit into a recess and allow the spar to be pushed through the fitting.

DF95 Stand with keel bulb holder. 

Keel straps onto one piece board with Velcro for safe and easy transport. 

Stainless hardware. 3M rubber strips on hull arms and Harken Sea Deck used on keel bulb holder. 

Made to order. Ships 1-2 days after order received. 

Customized DF95 Rig Locks. 

Slide on mast stub and insert jib boom counterweight to keep sails secured within rig bags to help protect the sails during transit. 

Sold in sets of 2. 

Printed in PETG or ABS. 

Nickel-plated brass fitting used primarily to form secure deck attachment points or fairleads

M3.5 threaded shaft and 2.5mm radiused eyelet hole. 

• Flysky FS-i6X is default 6CH with FS-iA6B Receiver. If you have 10 channels receiver FS-iA10B, that you can open to 10 channels.
• Bidirectional Communication --- Capable of sending and receiving data, each transmitter is capable of receiving data from temperature, altitude and many other types of sensors, servo calibration and i-BUS Support
• Low Power Consumption --- The system is built using highly sensitive low power consumption components, maintaining high receiver sensitivity, while consuming as little as one tenth the power of a standard FM system, dramatically extending battery life.

Ball bearing gooseneck fitting for 11mm mast extrusion.

Comes with screws to install into mast. 

316 Stainless Steel Headstay Hook

IOM, EC12, Soling, etc 

15.3 mm x 7.3 mm

Mint Carbon Covered Keel Bulb (Mint design)

Mint Carbon Keel Fin including stainless hardware

Mint Carbon Rudder